Mineral Oil Defoamer For Coatings

RK-170 is mainly use the large coefficient of osmosis of mineral oil and hydrophobic particles as antifoaming active material, supplemented by antifoaming synergistic substance. Mineral oil increase osmotic speed. The hydrophobic particles reduce antifoaming synergistic material into the barriers. The interaction provides great antifoaming performance. Meanwhile, mineral oil has good affinity with organic matter so that it doesn’t cause surface defect. ​

RK-1107 is a 100% active content mineral oil defoamer, which is specially designed for emulsion polymerization, suspension polymerization, emulsion adhesives, etc.. It’s very high efficiency, great persistence and compatibility. It’s also confirmed that it is effective for curtain coating. ​

RK-207 is a high efficient liquid(wetting) defoamer based on new polymer, which is combined with active antifoaming carrier oil components. It’s effective for fine resin emulsion and added into any processes of latex paint production, it’s also suitable for polymerization processes. Also, it has high compatibility with the system, no precipitation and formation of shrinkage cavities on the surface. ​

RK-203 is metal soap, wax mineral oil-based defoamer. It is mainly used in paper coating, textile printing, water based architectural paint emulsion and paint made by this emulsion, waterproof coating, etc. ​

RK-707 is mainly made of mineral oil with large expansion coefficient and hydrophobic particles as defoaming active substances, assisted by defoaming synergistic substances. Mineral oil increases the expansion velocity of defoaming particles, and hydrophobic particles reduce the entry energy barrier of defoaming particles. The interaction between the two provides excellent defoaming performance. At the same time, mineral oil has a good affinity with organic matter, so it will not cause surface defects. It is mainly used in the emulsion and latex of water-based coatings, and the adhesive made by the emulsion or latex and waterborne building coatings. The effect is more obvious in the system with higher viscosity. It also can be used in the leather edge oil. ​

RK-980P is a 100% active content mineral oil antifoam. It’s very high efficiency, great persistence and compatibility, which is suitable for acrylic acid, vinyl acetate, acetic acid, styrene-acrylic, copolymer emulsion, coating, resin, detergent, sewage treatment. ​

RK-40S is a multi-purpose silicone synthetic defoamer for non-aqueous systems. It is particularly suitable for foam control in oil-based inks for printed circuit boards and epoxy floor paint systems. It has good defoaming properties and can quickly eliminate small bubbles. ​

RK-T100 is a kind of defoaming agent with special emulsified and silica system, which hasexcellent dynamic defoaming, anti-foaming effect and long-lasting defoaming ability, especially under the harsh conditions. Very low addition can achieve the ideal defoaming effectand reduce the effect causedby adding largely amount defoamer.The special emulsified system makes the good compatibility, diluted stability and shear stability.​

RK-2200 is a general and special modified non-silicon defoamer, especially suitable for polyurethane, epoxy floor paint, solvent-free UV curing, polyester system, etc. It has excellent defoaming and antifoaming performance, balanced dispersibility and extremely high compatibility, and will not precipitate in the system and form shrinkage holes. ​

RK-23S is a kind of silicone defoamer, it has excellent defoaming&antifoaming performance at low dosage. It’s mainly used in textile printing & dyeing and water treatment processes. ​

RK-7470M is developed with a special silicone grease system, with specially designed emulsion system. It provides excellent antifoaming performance and balance, which makes sure the compatibility of system, excellent stability of dilution and shear. It’s suitable for metal cutting liquid. Little addition can achieve ideal foam control effect and reduce the negative effect on the finished products due to adding lots of defoamer. It is used in full synthetic cutting liquid and emulsion type cutting liquid. ​

T40 is a nonionic hydrophobically modified ethylene oxide urethane (HEUR) rheology modifier designed for waterborne architectural, industrial and functional coatings. It is a product of APEO and OrganoTin free. ​

RK-33S is a compound antifoaming agent. Under widely pH and temperature conditions, it has great performances with breaking foam fast and continuously. It’s suitable for areas with higher requirements of compatibility and transparency. And it’s widely used in daily chemical washing, laundry detergent, metal cutting liquid, textile, industrial cleaning, etc. ​

RK-76T has excellent defoaming and anti-foaming properties as well as excellent compatibility, and can effectively prevent microfoam generation in high and low viscosity systems. RK-76T is suitable for water-based systems such as container paints, wood furniture paints, architectural coatings, industrial coatings and water-based printing inks. ​

RK-77T is a modified silicone defoamer specially designed and developed for latex system. It has excellent anti-foam performance and good compatibility. It is suitable for industrial paints, wood paints, architectural and industrial paints, water-based printing inks and other systems in water-based systems. ​

RK-360 is a silicone polyether modified antifoam without precipitation after dispersing in the system. ​